() removal of external Grill plastic insert. remove the five (5) bolts from the grill. (Figure 2-1) (b) apply 1 7/8 "(48mm), mylar tapes are external bracket locations. (Figure 2-2) (c) open hood. attach external brackets using the nylon insert. (Figure 2-3) (d) to remove the 6 nuts in the grill to Hud locations. (Figure 2-4) (e) once the locks are removed from steps 2 (a) and 2 (d), Grill naturally must cause a gap at the top of the lid (Figure 2-5). If you need additional permission, slightly pushed the lattice to create a larger space. to account not to push extremely from lattice or outboard clips (not visible) can switch (Figure 2-6). (e) wash thoroughly. apply 3 mylar strips on the Hood and Grill, leave enough overlap to cover Hood. 43 "(1092mm) tapes to the centre section and add 4" (102 mm) pieces to cover the remaining area of the lid. (Figure 2-6) (g) gently slide shield spot and Center.

make sure that the shield is completely seated (Figure 2-7). If you need additional permission, slightly pushed the lattice to create a larger space. to account not to push extremely from lattice or outboard clips (not visible) can switch (Figure 2-6). Insert the screw through the center of the grill and Grill shield (Figure 2-7). (h) retighten all screws grille. (Figure 2-8). torque = 52 in-lbf (i) attach external brackets to cover with the aid of machine screws. (Figure 2-9) (j) to replace the bolts and replace the front Grill Grill plastic insert. (Figure 2-10) (k) remove masking from Hood protector. DownloadTundra Hood protector installation of 2007 Toyota

remove existing exhaust system. (1) remove the two bolts with springs of the front flange, located between the catalytic converter and rear muffler. (Figure 2-1) (b) keep all bolts of the original equipment (OE) and springs. (Figure 2-1) (1) ensure that the original Gasket between the remains of converter Assembly belt note: Dio, must be replaced install Gasket between the – p/n 17451-74051. (c) remove the two bolts from the rear flange, located between the muffler Assembly and installation of rear exhaust tailpipe is discharged.

(fig 2-2) (d) pry loose from rubber hanger, located near the rear bumperrear Calliper tailpipe exhaust. (Figure 2-3) (e) remove the Assembly of the oe rear tailpipe from the vehicle. pry the two front muffler exhaust brackets loose rubber handles. (Figure 2-4) (g) pry the two rear muffler exhaust brackets loose rubber handles. (fig 2-5) Note: the use of lubrication (for example "SOAP and water") of rubber exhaust handles can facilitate the removal and installation of rubber handles. (h) do not remove the five (5) original (OE) rubber handles from the vehicle. (i) remove the oe muffler Assembly from the vehicle. 3. install trd System. (1) connect the two front muffler handles the muffler Assembly of trd oe rubber handles. Download2007 Toyota Fj Cruiser for muffler installation guide

internal installation of switch/wire harness () locate the vehicle, White 6-PIN connector behind the lower instrument panel. (Figure 2-1) (1) Note: connector of the vehicle will be wrapped in gray foam tape. (b) installation of remote time switch (Figure 2-2), in available knockout (location 1 or 2), and in the orientation shown. (Figure 2-1) (c), plug the 6-pin white connector in the key. (1) confirm the connector is firmly attached. (d) the removal of the driver and passenger side visors. (1) rotate and loosen shaft support visor from visor holder clips as shown. (Figure 2-3) (2) does not remove clips from popular actor. (e) remove the sun visors (Figure 2-4) (1) remove the two Phillips screws (2) from the driver and passenger side visors.

To remove the driver and passenger side Assist grips. (1) remove the screw covers for all the claws four (4) assistance. (Figure 2-5) (g) remove the two (2) 10 mm hex head screws from the driver and passenger assist grips. (Figure 2-6) (h) "" pillar garnish to remove front passenger. (1) pull door seal around front "pillar". (2) places the two (2) videos and one (1) nail and remove the front pillar garnish. (Figure 2-7) (i) remove the front pillar garnish driver. (1) using the same procedure as the passenger's side. (j) to remove the mirror. (1) remove the mirror base mountain cover by careful insertion tool for Remove panel , as shown. Download2007 Toyota Fj Cruiser air dam/light bar installation

Attention: do not forget to read the precautionary statements system of Srs cushion before servicing, refer to systems of service restriction. 1. disconnect the negative battery Terminal warning: at least 90 seconds after disconnecting the negative terminal, wait-the battery to prevent belt Pretensioner () activation and air bags. 2. Remove the direction the whole pad a. face of the front wheels. B. using a T30 Torx "driver, loosen two screws while a Groove along the length of each lap of screw catch in case of screw. C. download platform of the steering wheel and the management of maintenance of the keypad with one hand, as shown in the illustration.

Note: on the abolition of the D-pad, does not download cushion Wire harness. (D) using the screwdriver, disconnect the connectors 2 cushion. Attention: When the management of cushion clutch will not damage cushion Wire harness. E. disconnect the connector Jack and remove the plates to the direction. Installation warning: don't forget to read the precautionary statements system of Srs cushion before servicing. 1. install the platform management direction a. support pad with one hand, as shown in the illustration. B. connect the two air filters. Note: when handling cushion clutch will not damage cushion Wire harness. C. connect the Horn. (D) to install the Steering Panel after confirming that the slots of the circumference of the screws are traps in the event of a screw. DownloadToyota Rav4 2Wd truck Steering Panel for removal and installation of 2007

1. align the steering wheel . (a) where it is centered parking to install leather steering wheel, the position of the vehicle, so that the front wheels are straight and the steering wheel vehicle. (1) turn the steering wheel rights position. (2) apply masking tape to the top center of the steering wheel and the steering column upper cover. (Figure 1-1) (3) draw a line bar masquerading as shown in the illustration. (Figure 1-1) 2. Remove battery cable. () remove negative battery cable.

(Figure 2-1) (1) protection of wings before you begin. (2) do not touch the positive terminal with any instrument in the removal of the cable. (b) srs cushion system backup power is active for 90 seconds after the negative cable is disconnected from the Terminal. Wait 90 seconds after the battery of the vehicle is disconnected before beginning step 3. (for safety cushion). Download2008 Toyota any Xd/Xb steering wheel alignment

1. remove the following parts: end of a. b. bottom panel glove compartment door c. lower panel complete with no. 2 2. Final panel remove cluster a. Remove key, A/management of c. b. Pull the enemy. C. Remove heater control plate. D. Remove 2 screws. E. using a screwdriver, remove the 4 mounting clips and the Panel is downloaded, then unplug the connector. Tip: Tape the tip of the screwdriver before use. 3. disconnect the cables Hater control tip: After connection, adjust the control cables. 4. to remove all control of heater remove 2 screws and remove the heater control Assembly, and then disconnect the connector. Installation of the installation is in reverse order of removal.

Tip: after the installation, set the heater control cables. A. mounting set control enemy under the following conditions: 1. the placement of the heater control Assembly in the "Cool" position. 2. "face" position 3 of dialing mode control . Temperature control dial for "Cool" position (b). set air intake cable. Pull my relationship of control as "Cool" position, connect cable and clamp bolt. Tip: Locking Pliers, lightly pressing on the outside of the cable in the direction as shown in the illustration. C. adjust the arrangements for power management. Pull my relationship of control as the "face" of the position, connect cable and clamp bolt. Tip: Locking Pliers, lightly pressing on the outside of the cable in the direction as shown in the illustration. Download1998 Toyota truck Tacoma extra cab 2Wd control Assembly removal and installation

Caution: disconnect the cushion before removing the steering wheel pad. 1997 Cushion restraint system or cushion article restriction. Remove 1. Place the front wheels turned forward in a straight line. 2. to remove the flywheel. Panel, see Remove wheel. 3. the engine must be switched off. Remove the flywheel nut. The wheel and place Matchmarks on the main axis. Use a set of Extractor c: Hanger 150, shoulder slide, Center of bolts, 150 and no. Nail 2 (SST 09920-50010, 09551-05010, 09552-05010, 09953-05020, 09954-05020), remove the wheel. See fig 27. Figure 27: removing the wheel arrangement of Toyota Motor sales, Inc., United States 4. Remove federšajbite PIN and remove the nut.

The use of a spherical exhaust (SST 09,610 to 20.012), a separate Tie rod end joint of the address. See Figure 28. Figure28: Rod separation connect points of steering ankle concert Toyota Motor SalesInc., United States, 5. Place Matchmarks on the intermediate shaft and axle of the regulating valve. See Figure 29. Screw a loosen and remove the bolt (b). Figure 29: disconnect the intermediate shaft 6. Off the plate. Remove the nut. 7. disconnect the pressure for power and pipes. Using the wrench 14 X 17 mm power steering hose the nut set (SST-09631 22020), turn off the tube. See fig. 30. Download1997 Toyota Avalon Xl steering removal and installation

1. vehicle preparation. (fj Cruiser shown) () vehicle must be on the ground and not of incline/decline. (b) fully engage parking brake. (c) to remove the shift cover lock release. except for re-use. (Figure 1-1) (d) is pushed into the shift lock release button. (Figure 1-2) (e) place shifter the lowest gear. (Figure 1-3) 2. to remove oe shift button. () remove oe shift knob from turning o'clock counter-philosopher. (b) reject oe shift knob 3. Install the Shift button. (2) shift knob is installed rotate o'clock-wise. (1) when fully installed, there should be a 1/2 "+/-3/32" (12 mm +/-2 mm) gap between the bottom of the knob shaft to shift and shift gate,

the upper surface. (2 "barrel" of the shift knob must be oriented in the vehicle. (3) place a lever for change in "Park". (4) replace the shift cover lock release. (5) should be trimmed shift knob with-Scratch cloth. Download2007 Toyota Tundra sport Shift knob installation

Pension 1. Loosen water pump pulley. 2. Download the drive belt idling adjustment screw and remove the belt. 3. Remove the pump pulley water pump. 4. to remove the bolt on the crankshaft pulley Assembly. 5. with the help of SST (09213-31021), remove the crankshaft pulley. 6 Remove bolts and nuts supply chain, as shown in Figure 7. the use of a plastic hammer, loosen at the top of the chain and remove user. 8 remove the drive chain tensioner and time, vibration damper. Budget bolt remove the camshaft sprockets. 10. remove the chain and authority setting inbound. 11. remove the running body with a screwdriver.

If running body you cannot remove with screwdriver, using SST (09213-36020). Installation 1. Install running authority. 2. Set No. 1 TDC. 3. align the camshaft PIN with push plate. 4. to install the body to the circuit of the camshaft. Note: align supply chain and camshaft body mark time. 5. to install the distribution chain to the crankshaft body. Note: align supply chain and crankshaft body marks time. 6. to install body with chain camshaft. 7. Install and tighten the incoming body. Denomination: 54 to 63.5 Nm (40-47 Ft Lb.) 8. Install the drive chain tensioner regulator of vibration. Note: Apply oil tensor before installation. 9. Cover the installation time string Download1984 Toyota Starlet L4-1290Cc 4Ke time chain service and repair

Note the instructions for installation: for easier mounting and installation, vehicle and all snowplow components must be of smooth, level, hard surface, such as concrete. 1. on the side of the driver of the machine remove the remote clip securing the plastic bumper cover to start the dish. keep the knee to reinstall if the plow is removed. then fold the outermost of the plastic bumper cover for easier pushplate installation. 2. trim the splash Pan, as shown for easier pushplate installation. 3. Repeat steps 1 and 2 on the passenger's side. 4. on the driver's side of the machine remove the tow hook clasps and hook for towing. maintain a tow hook to reinstall if the plow is removed. keep the locks for reinstallation of the next step. 5. attach the driver's side to the frame of the pushplate truck, using the original latches hook towing. tighten hinges, so that the pushplate can be firmly against the bottom of the frame, but not fully reinforced at this time. 8.4-7 of the steps on the side of the machine is repeated. 9. to install the cross bar with four 1/2 "x 1-1/2" cap screws and 1/2 '' locknuts. hand tighten fasteners. 10. check connecting hand distance of 29-1/8 "+ 1/8". If the connecting arm distance is not within the 29-1/8 "+ 1/8 '', then loosen tow hook latches of either of the two pushplates and pushplate (s) in the direction to get move Download2007 Toyota Tundra mounting kit installation instructions

Use the following replacement pads for that State. Repair procedure 1. Remove the front wheel. 2. check the front pads for any irregular wear, loosening two bolts on the brake caliper Assembly. 3. remove the brake caliper and support it to avoid damage? the plastic line. 4. check the front brake pads for wear. If excessively worn pads, then replace the pads with the new part. 5. Add grease caliper disc brake pad clips on both sides support and anti-squeal shims. In Figure 3. Figure 4. 2 1 1 No. 1 disk brake pad support plate 2 No. 2 disc brakes pad support plate:

Production changes at the transponder key ECU. Use the following procedure to repair a client to resolve these problems. Repair procedure 1. Make sure that the vehicle will crank but will not start. 2. validate health and find any system immobilizer DTCS. 3. If there are any immobiliser DTC now, check the vehicle with the help of all keys. If the condition with all keys, skip to step 4. If the problem of isolated single key, refer to repair manual diagnostic chart for speci? with DTC. 4. replace the transponder key ECU. • 2007/2008 Tundra: the Interior of the car-theft deterrent/Keyless entry-engine immobiliser transponder key ECU is: delete transponder key ECU and Assembly is located on the air conditioning unit between the bulkhead on the left side. B. back side of air-conditioning units, where the transponder key ECU Assembly. C. Remove transponder key ECU from air conditioning units, sliding lower half out and travel down to

Engine starts normally after you move the shift lever in neutral or cycling the shift lever and exit the Park position. Neutral start switch Assembly revised is available for this condition. Repair procedure 1. Replace the neutral start switch Assembly. Technical information system (MIS) is a model and model year repair Manual: 2008 Highlander: • transmission automatic transmission/Transaxle automatic gearbox – the automatic Transaxle automatic gearbox U151E: Park/neutral position switch: removal/adjustment/preferences • transmission automatic transmission/Transaxle automatic gearbox – "U151F automatic Transaxle automatic gearbox: Park/neutral position switch: removal/adjustment/settings" 2009 Highlander: • transmission automatic transmission/Transaxle automatic gearbox – the automatic Transaxle automatic gearbox U151E: Park/neutral position switch: removal/adjustment/preferences

Introduction, some customers may complain to one of the following conditions is true: S grinding during changer s difficulty in attracting or Edition 4WD low s uncomfortable foot or leg position with the clutch pedal fully depressed the clutch pedal Assembly and the carpets were changed to improve the clutch pedal feel and exploitation. Repair procedure for a carpet modification 1. Remove the front door scuff plate LH. Disconnect and remove the front 9 claws door scuff plate. 3. remove the cowl side trim Board LH. A. remove the clip. B. separation 2 clips and remove the cowl side trim Board. 4. Cut the carpet felt backing (padding). A. turn the left front floor carpet. B. Mark the position where the foam front deck before deleting. Note: the S Word Pad color of previous front (P/N 58571-04060): cream yellow s color from the new front floor pad (P/N 58571-04070): black c. remove front floor foam pads on the rear floor carpet. D. cut felt, laying on the back of the carpet floor without cutting a rug with a knife carpet, adjusted only to the depth of the felt pads. Cut the felt, the fields

Some users may encounter during acceleration, which is most noticeable after the cold soak the ticking or tapping noise from engine-type area at 2000-2500 RPM. New manifolds were designed to minimize this condition. Part of the information the previous number 17140-17150-17173 0P010 0P010 – 0P010 current number 17140-17150-0P070 0P070 of the name, exhaust manifold Assembly, RH manifold Assembly, exhaust gasket, exhaust manifold LH QTY 1 1 2 replace procedure repair LH and RH exhaust manifolds. Refer to the technical information system (LIS) Jung, 2005 or 2006, Tacoma repair manual 1GR-FE engine: mechanical: partial engine Assembly: replacement. Warranty information code OP EG5027 applicable warranty *: remove & reinstall (R & R) of the exhaust manifold (P/N 17140-17150-0P010 and 0P010) is attached the catalytic converter, the Federal emissions warranty Toyota. This guarantee is valid for 96 months or 80000 miles, whichever comes first, from

Some clients may experience Squeak noise due to contact between a track, and search for a contact? ½ Pan hole (s) location. The following procedure describes the repair method to fix this condition. 1. disconnect the negative battery terminal (-). 2. remove the plastic cover over the front seat track, use a plastic pry tool carefully remove the claws and the plastic seat cover track. Note see. Appropriate Toyota repair manual for each model for detailed instructions on how to remove the plastic cover of the seat track. 4. remove the LH front seat. A. Move the seatback fully upright position. B. removing four (4) track mounting bolts. C. disconnect electrical connectors and remove the complete seat. 5. remove the seat track, search for contacts. A. seat from the vehicle to tilt the seat back have access to contacts of the locking of the seat track. B. using powerful means of production cut two (2) search for contacts, leaving 2 mm (0.1 inches) or less from each PIN. • Note do not allow production tool contact place of the track. JUST cut off the shaft PIN (near the base of the track).

Some clients may complain of excessive sulphur smell of 2006 year model year Tacoma vehicles the 1GR-FE (V6) engine: S to stop and go driving s heavy acceleration to reduce the smell of sulphur, new catalytic converter Assembly. Follow the procedure to repair an Assembly to replace the catalytic converter. Note: for a better understanding of the causes, refer to TSB # EG003-03, "sulphur Smell from exhaust gases. Repair procedures, refer to technical information system (LIS): 2006 model year Tacoma repair Manual: exhaust: the exhaust pipe assy (1GR-FE).