Showing posts with label hyundai. Show all posts

DIAGNOSIS AND REPAIR Hyundai SONATA NF XM SET TOP BOX

By manuels | Published Monday, October 29, 2012

PROCEDURE: A). When diagnosing a vehicle with an inoperative XM Set Top Box, check for water intrusion into the set top box. If no water damage is noted proceed with normal diagnostics. If water damage is noted then proceed to Step B. B). 1. Remove Set Top Box a. Gain access to trunk and remove trunk pad/carpet b. Remove 2 mounting screws attaching set top box to the body c. Disconnect box from harness 2. Visually inspect body for signs of water intrusion.


Without Sunroof or AMP With Sunroof and AMP 3. Note that water may enter at body seams, screw holes, body plugs, or weld joints. 4. Reseal all joints and any other suspect water entry point with appropriate body sealer sealant.

Hyundai SONATA NF XM SET TOP BOX DIAGNOSIS AND REPAIR download
Read More DIAGNOSIS AND REPAIR Hyundai SONATA NF XM SET TOP BOX
Posted in |

3.8L M/T HYUNDAI GENESIS COUPE ENGINE RPM CONTROL LOGIC UPDATE

By manuels

If the vehicle has been in storage for days, run the engine to ensure an adequate battery charge state for reliable update results. 2. Turn off all lamps (Do not leave head lamp switch in auto mode) and all accessories (including heater, A/C, blower, radio, seat warmer, defroster, etc.) to prevent the battery discharge during the update. 3. Perform the update with the ignition switch in the ON position. 4. Be careful not to disconnect any cables connected to the vehicle or scan tool during the update. 5. Do not start the engine during update. 6. Do not turn off the ignition switch during update. 1. Connect the power supply cable to the diagnostic terminal. NOTE: If attempting to perform the update with the power supply cable disconnected from the diagnostic terminal, make certain that the diagnostic terminal is charged enough for the update. If not, the update may fail in progress.


Therefore, it is strongly recommended to connect the power supply cable to the diagnostic terminal during the update procedure. 2. Connect the USB cable between the VCI and the diagnostic terminal. NOTE: When performing the update using the GDS, wireless communication between the VCI and the diagnostic terminal is NOT available. Therefore, be sure to connect the USB cable between the VCI and the diagnostic terminal. 3. Connect the 16-pin DLC cable from the VCI into the vehicle’s 16-pin connector under the driver side instrument panel. 4. Turn on the VCI and diagnostic terminal with the ignition key in the ON position. NOTE: Do not start the engine. download

Read More 3.8L M/T HYUNDAI GENESIS COUPE ENGINE RPM CONTROL LOGIC UPDATE
Posted in |

Hyuandai AZERA and SONATA Temperature Replacemen Manual

By manuels | Published Wednesday, September 26, 2012
Hyuandai AZERA and SONATA Temperature Replacemen Manual
DESCRIPTION: On few vehicles the ambient temperature displayed on the status somebody may dissent from the existent outside temperature by writer than 5-10oF. An updated ambient temperature device is getable to amend this procedure. This TSB provides the work to install the updated ambient temperature sensor settled in beguiler of the radiator/condenser.
" Model / Strained object creation date arrange: " Azera (TG): Produced Job 1 - Jan 8, 2006 " Sonata (NF): Produced Job 1 - January 8, 2006 Substitution PROCEDURE: 1. Unfasten the ambient temperature sensor mounting rushing. 2. Disappear the ambient temperature device by disconnecting the wiring connector. 3. Connect the wiring connector to the new sensor. 4. Tighten the ambient temperature sensor mounting decamp. 5. Set the A/C examine psyche after ambient temperature device substitution. " Azera - Shift for 15 seconds the Powerfulness Connector Fuze (30 amp) from the traveller compartment connecter stop and follow. " Sonata - Shift for 15 seconds the Superpower Connector 2 Ignitor (15 amp) from the rider compartment connection cube and lay
 download
Read More Hyuandai AZERA and SONATA Temperature Replacemen Manual
Posted in |

Hyuandai Azera KEY CUTTING Procedure and Programming

By manuels | Published Thursday, July 19, 2012
Hyuandai Azera KEY CUTTING Procedure and Programming
PROCEDURE: When an owner loses an Azera immobilizer key, the customer has two options to replace the lost key. Both options require that the customer bring the vehicle and any remaining keys to an authorized Hyundai dealer. Option # 1 The customer can use any remaining key originally supplied with the vehicle to drive to an authorized Hyundai dealer and request that a new key or key set be cut and programmed. It is important that the customer bring any remaining keys with them to the dealership. Any key that is not programmed (or re-programmed in the case of originally supplied keys) in the same operation will no longer start the vehicle. Option # 2 The customer can have the vehicle towed to an authorized Hyundai dealer and request that a new key or key set be cut and programmed. Again, it is important that the customer bring any remaining keys with them to the dealership. Any key that is not programmed (or re-programmed) in the same operation will be unable to start the vehicle. 1. If the Hyundai dealer does NOT have a Barnes Distribution BD Laser, they MUST call the Hyundai Motor America Parts Call Center at 1-800-545-4515 and make a request (order) for Azera immobilizer keys to be cut. NOTE: Azera immobilizer key blanks can be ordered either in singles (i.e. 1- master) or complete key sets (i.e. 2-master keys and 1-sub or valet key).
Nonetheless, HMA Parts System Centers gift exclusive pre-cut rank key sets upon communicate. They give NOT cut individual creation keys. 2. The Hyundai financier Staleness give the pursuing collection to the HMA Parts Inclination Middle. " VIN " Key Encipher " Moneyman Inscribe " Moneyman Accost (correct conveyance speak) " Moneyman Impinging (accurate denote of who the key should be delivered to) " Junction Phone Amount and Education 3. The HMA PDC testament help the conveyance of the key(s) to the concern de {must be programmed to the vehicle using a Hi-Scan Pro means. Mention: The Azera is accoutered with immobilizer anti-theft technology that instrument not grant the newly cut keys to signaling the object unless they bonk been gear programmed to the vehicle.
Read More Hyuandai Azera KEY CUTTING Procedure and Programming
Posted in |

Hyuandai Genesis Coupe Owner Manual

By manuels
Hyuandai Genesis Coupe Owner Manual
TGS Commutation 1. Place the vehicle so it may be lifted on a lift and release the parking constraint. 2. Unbutton the modify lever kicking catch (A) and unprotected the shift lever flush. 3. Withdraw the fissure tumbler thickening by turning it counterclockwise. 4. Build the container off the percept and remove the energy armor by unfastening 6 mounting bolts (B). 5. Unfasten the two nuts (C) at the projection in fore of the catalytic convertor. Remark: Torque specification: 28.9 ~ 43.4 lb-ft. 6. Unfasten the two nuts (D) that introduce the parcel hanger on the lineman cylinder and vanish the area tubing unitedly with the thirdhand catalytic device. 8. Stretch a someone conductor across the anterior propeller upright caoutchouc connector (a) and the transmittal familiar projection(b). This leave be utilized to align when reinstalling. Discretion: Use fix not to exchange locations and directions of bolts and washers when reinstalling to forestall placement issues. 9. Disappear the 3 propeller airway mounting nuts Alter propellor upright to increase accession to the motion lever.
download
Read More Hyuandai Genesis Coupe Owner Manual
Posted in |

Wiring Connector Manual Guide Hyuandai ELANTRA CORROSION

By manuels
Wiring Connector Manual Guide Hyuandai ELANTRA CORROSION
A facility leakage between the trickster outmost panel and cowl panels may resultant in corrosion of the proximity entranceway wiring connector pins if the object is operated in areas where means seasoning is utilized. The corroding may strike the cognition of the electrical circuits in the entryway, much as the speakers, nation windows, etc. To correct this status, reseal the seams and inspect the entrance wiring connectors for corrosion. If needful, position the entryway wiring connector and the entryway wiring by followers the couple procedures described in this TSB. SEALING THE Committee SEAMS: Comment: This sealing process applies to both nigh and modify sides.
1. Open the hood. 2. Locate the “A” pillar outer panel and cowl panel seaming area at the base of the “A” pillar. 3. Lift up the lower end of windshield glass molding to obtain space for sealant application. 4. Clean the sealant application area on both the left and right sides of the vehicle (fender removed in photo for clarity). 5. Apply clear sealant along the seam line between “A” pillar panel and cowl panel from the engine compartment as shown in the photo. 6. Use appropriate tool or finger (with rubber nitrate gloves) to smooth material to seal the sealant. NOTE: Apply enough sealant to completely fill the seam. Be careful not to drip excess sealant in the engine compartment or on the hood. – Photo shows panel seams where sealant is applied on left side. – Repeat for the right side. 7. Open the front door. 8. Apply the clear sealant to the seam between “A” pillar panel and the fender mounting bracket from inside the door opening. 9. Apply the clear sealant to the bottom of the fender mounting bracket and the top of the hinge. 10. Use appropriate tool or finger (with rubber nitrate gloves) to smooth material to seal the sealant. NOTE: Apply enough sealant to completely fill the seam. Be careful not to drip excess sealant on the door trim or in the interior. – Sealant is applied along the top edge of the fender bracket.

download from here
Read More Wiring Connector Manual Guide Hyuandai ELANTRA CORROSION
Posted in |

2002-2003 Sonata and XG350 FUEL TANK ASSEMBLY VALVE INSTALLATION

By manuels | Published Monday, May 28, 2012

This TSB provides the procedure to remedy this condition by installing an additional fuel tank assembly valve. For Sonata and XG350 vehicles (Please see pages 8-10 for Elantra and Tiburon vehicles): 1. Raise the vehicle. 2. Remove the three muffler hangers and support the rear muffler after it has been lowered 6 inches. NOTE: Do not allow the muffler to hang unsupported. Do not lower the muffler more than 6 inches. 3. Remove the rear suspension crossmember mounting bolts and lower the suspension crossmember. 4. Support the fuel tank using a jack stand. 5. Remove the left rear fuel tank band nut and lower the band from the mounting stud. 6. Disconnect the vapor hose from the ‘Y’ shaped tube. 7. Cut about 4 inches (100mm) from the end of the

Read More 2002-2003 Sonata and XG350 FUEL TANK ASSEMBLY VALVE INSTALLATION
Posted in |

Hatch Back Cylinder Head Assembly Removal and Installation 2000 Hyundai Accent L

By manuels

1. 2. 3. 4. 5. Drain the coolant and disconnect the upper radiator hose. Remove the breather hose (between the air cleaner and the rocker cover). Remove the air-intake hose. Remove the vacuum hose, fuel hose and coolant hose. Remove the cables from the spark plugs. The cables should be removed by holding the boot portion. Remove the ignition coil. Remove the surge tank. Remove the intake manifold. Remove the heat protector and exhaust manifold assembly Remove the coolant pump pulley and the crankshaft pulley. Remove the timing belt cover. 6. 7. 8. 9. 10. 11. Zoom Sized for Print 12. Move the timing belt tensioner pulley toward the coolant pump and temporarily secure it. 13. Remove the timing belt. 14. Remove the rocker cover. 15. Remove the cylinder head assembly. The cylinder head bolts should be removed using Special Tool, Cylinder Head Bolt Wrench (09221-21000), in the sequence as shown in the illustration. 16. Remove the gasket pieces from the cylinder block top surface and cylinder head bottom surface. NOTE: 1. Make sure that the gasket pieces do not fall in to the engine. INSPECTION 1. Check the cylinder head for cracks, damage and coolant leakage. 2. Remove scale, sealing compound and carbon deposits completely.

Read More Hatch Back Cylinder Head Assembly Removal and Installation 2000 Hyundai Accent L
Posted in |

1996-2000 Hyundai Elantra Repair manual

By manuels

DESCRIPTION The following vehicles share common transaxle Diagnostic Trouble Codes (DTC): • 1996-2005 Accent • 1996-2000 Elantra • 1997-2001 Tiburon Elantra and Tiburon vehicles produced beginning 6/1/99 and 2000-2005 Accent vehicles use a valve body with six solenoids and have several new DTCs. DTC information can be found in the shop manuals, TSBs and Engine Fault Code Diagnostic Manual (OBDII Manual) listed below: DTC P0501 Vehicle speed sensor range DESCRIPTION P0703 Stop lamp switch – Open/short P0705 Range switch signal problem P0707 Range switch – open circuit P0708 Range switch – short circuit P0710 A/T fluid temperature sensor P0711 A/T temperature sensor – rational- ity check DTC P0712 A/T temperature sensor signal – open/short P0713 A/T temperature sensor signal – open/short P0717 No pulse generator A signal P0722 No pulse generator B signal P0727 Engine speed signal

Read More 1996-2000 Hyundai Elantra Repair manual
Posted in |
Powered by Blogger.

Search