Disconnect battery. Disconnect harness multi-plug from engine coolant temperature (ECT) sensor Fig.1 [2] . Disconnect harness multi-plug from mass air flow (MAF) sensor Fig.1 [4] . Remove protective cover Fig.1 [1] . Remove plastic tube from wiring harness Fig.1 [3] . Remove insulation tape from wiring harness. Cut engine coolant temperature (ECT) sensor wiring and remove from cable ducting.
Cut new engine coolant temperature (ECT) sensor wiring a minimum of 120 mm long. Fit new wiring harness multi-plug to wires Fig.2. Repair wiring with repair kit listed. Seal with insulation tape Fig.3. Remove engine coolant temperature (ECT) sensor. Fit modified engine coolant temperature (ECT) sensor. Tightening torque: 18 Nm. Refit wiring harness multi-plug. Reconnect battery. Erase fault memory. 1995 – 2001 VAUXHALL Vectra 2.5 i Poor starting from colddownload
To lower Turn rotary switch to d. Posit ion memory After the ignition has been switched on, the sunroof c an be automatically returned to its last position b y briefly pressing the rotary switch. Safety function If the sunroof encounters resistance during automatic closing, it is immediately stopped and opened again, as long as the vehicle is stationary. Operated using rotary switch in the overhead control panel.
To open Turn the rotary switch to any position between d and ü. The sunroof will automatically move to the desired position. When the switch is in position ü , the sunroof is fully opened . Com fort position Set rotary switch to position f.
With the roof in this position, w ind noise is reduced. To close: Turn rotary switch to d. 9 Warning Closing sunroof from outside To close the sunroof from outside with the remote control: Press button p until the sunroof is closed. If the electric windows 3 are to be closed from outside the vehicle, but the sunroof is to be left op en, briefly press the rotary switch before switching off the ignition. download
PROCEDURE: A). When diagnosing a vehicle with an inoperative XM Set Top Box, check for water intrusion into the set top box. If no water damage is noted proceed with normal diagnostics. If water damage is noted then proceed to Step B. B). 1. Remove Set Top Box a. Gain access to trunk and remove trunk pad/carpet b. Remove 2 mounting screws attaching set top box to the body c. Disconnect box from harness 2. Visually inspect body for signs of water intrusion.
Without Sunroof or AMP With Sunroof and AMP 3. Note that water may enter at body seams, screw holes, body plugs, or weld joints. 4. Reseal all joints and any other suspect water entry point with appropriate body sealer sealant.
Hyundai SONATA NF XM SET TOP BOX DIAGNOSIS AND REPAIR download
If the vehicle has been in storage for days, run the engine to ensure an adequate battery charge state for reliable update results. 2. Turn off all lamps (Do not leave head lamp switch in auto mode) and all accessories (including heater, A/C, blower, radio, seat warmer, defroster, etc.) to prevent the battery discharge during the update. 3. Perform the update with the ignition switch in the ON position. 4. Be careful not to disconnect any cables connected to the vehicle or scan tool during the update. 5. Do not start the engine during update. 6. Do not turn off the ignition switch during update. 1. Connect the power supply cable to the diagnostic terminal. NOTE: If attempting to perform the update with the power supply cable disconnected from the diagnostic terminal, make certain that the diagnostic terminal is charged enough for the update. If not, the update may fail in progress.
Therefore, it is strongly recommended to connect the power supply cable to the diagnostic terminal during the update procedure. 2. Connect the USB cable between the VCI and the diagnostic terminal. NOTE: When performing the update using the GDS, wireless communication between the VCI and the diagnostic terminal is NOT available. Therefore, be sure to connect the USB cable between the VCI and the diagnostic terminal. 3. Connect the 16-pin DLC cable from the VCI into the vehicle’s 16-pin connector under the driver side instrument panel. 4. Turn on the VCI and diagnostic terminal with the ignition key in the ON position. NOTE: Do not start the engine. download
