1. Remove the original bumper:
Remove all screws that hold the bumper. Also remove the screws the alloy handlebars and remove the bumper with alloy handlebars. Remove the alloy from the bumper and the new Hofele-design bumper install.
2. Placement of the front bumper Hofele-design on the car:
Put on it the new bumper on the car, but not even screw.
3. Preparation of the bonnet:

This handout is provided to you through the steps necessary to upgrade your vehicle with our performance chips run. Also note, that APR is just a call away you should all have any questions or concerns in relation to products Apr.

The steps for this Audi A4 brake installation manual
PREPARATION FOR THE INSTALLATION
1. Make sure that the vehicle on level concrete is parked and the parking brake on.
2Nd place keeps front and behind rear tyres.

Preparation Steps for Fuel System Installation
A: Adjust both seats to full forward position with seat backs in full upright position.
B: Disconnect the negative battery cable.
C: Remove the 5 rear interior panels starting with the long piece across the width of the car just beneath the rear glass. Next remove the two flat panels located behind the seats. Next remove the two corner pieces. Lastly, remove the rear center speaker and cover assembly. (The long panel across the width has 3 push lock barbed style securing pins w/one on each end and one in the center)

Thank you for purchasing the Comptech Icebox Cold Air Intake for the 2002–2003 Honda Civic-Si and 2001 – 2003 Acura RSX. All components have been designed and manufactured utilizing the latest in technology and materials. Comptech recommends that you read through these instructions before starting installation and that you use an Acura Factory Shop Manual to supplement these instructions.
All Comptech products are intended to be installed by a professional installer. Always use jackstands to support the vehicle when a car lift is not available. Always work in a clean environment and

Thank you for purchasing the Comptech Icebox Intake kit for the Acura TSX. All components have been designed and manufactured utilizing the latest in technology and materials. Please take a moment to read this instruction manual and warranty information page thoroughly before starting any work. Remember to always use jackstands to support the vehicle when a car lift is not available. Always work in a clean environment and use the appropriate safety equipment and tools to avoid any potential damage or injuries. Comptech recommends the use of a Genuine Honda Service Manual to supplement these instructions.

What is the SmartMAP??
The SmartMAP? model SS-300 replaces the check valve and restrictor assembly used by most Honda/Acura turbo and supercharger kits and prevents the engine computer (ECU) from shutting down the engine when the manifold pressure is above atmospheric (boost).

How does the SmartMAP? work?
The SmartMAP? connects inline with the stock (OEM) manifold absolute pressure (MAP) sensor and limits the MAP voltage that is applied to the ECU. The limit (clamp) voltage value is preset and can not be adjusted.

Most 18” wheels will clear the outer diameter of the caliper on a 355mm kit. However, the more critical clearance is the gap between the spokes of the wheel and the face of the caliper. Do not assume that a 19”, 20” or even 24” wheel will clear the face of the caliper. The actual metal-to-metal distance measured from the stock rotor face to the inside of the wheel spokes is 62.25mm for the BMW X5 front kit. StopTech recommends at least 2mm of additional clearance. See the Wheel Fitment Drawing page on the StopTech website for more specific measurements, at www.stoptech.com.

Most 17” wheels will clear the outer diameter of the caliper for a 328mm or 332mm rotor kit. For a 355mm kit, a minimum 18” wheel is typically required, and for a 380mm rotor kit, a minimum 19” wheel is needed. The more critical clearance, however, is the gap between the spokes of the wheel and the face of the caliper. Do not assume that a larger-diameter wheel will automatically clear the face of the caliper.

What’s Included:
1. The Model 80 enclosure bottom
2. The Model 80 vinyl covered enclosure top
3. Alumapro Alusonic 8 subwoofer (optional)
4. Subwoofer grille (optional)
5. Terminal cup
6. Self-adhesive gasket foam
7. Trim cord
8. (8) #10 x ¾” Phillips pan-head screws
9. (4) #14 x 1” hex-head sheet metal screws
10. (4) 1” fender washers
11. (4) 3/8 ” thick rubber washers
12. (12) 1 / 16 ” thick rubber washers
13. (4) #8 x ½” Phillips head machine screws
14. (4) #8 hex nuts

What You Will Need:
1. Power drill
2. 5/16”, 3/16”, 9/64”, and 1/8” drill bits
3. Philips screwdriver
4. 3/8” socket driver or wrench
5. Stiff-blade putty knife or similar flat bladed tool
6.Coping saw or hacksaw blade holder & blade

A phone prewire extension harness(center console to left side trunk, illustration 1) must be installed on the E46 (328i, 328iA) produced the first two weeks of 6/98 if the phone kit is being installed. The phone prewire option SA640 was not installed on vehicles produced during the first two weeks of 6/98. E46’s produced after the second week of 6/98 will have this phone prewire option SA640 installed at the factory.

Special Instructions for Air Connections
1. To cut the tubing correctly an appropriate cutter must be used (not a scissors)
2. When inserting the tubing into the connection it must be pushed in approximately 14mm until a click is heard.
3. To remove the tube, push the flange on the connection and at the same time pull the tube. (No tool is necessary.)
4. ATTENTION, when a tube is removed it is important to trim 14mm from the end before reconnection.
5. IT is advisable that LOCKTITE be used on the threaded fittings.

Important
•

Here are the steps for Mercedes-Benz E-class W211 installation/interface:
1. - Interface module completely set
2. Remote function & connect-function
3. Disassemble Guide
To connect interface command system and transmission in the district must release
After move - lever to drive mode, drag transmission as the direction of the arrow

A. Insert you A. a piece of tape over the edge of the hood and the edge of the fenders as shown right. Hereby, brackets and parentheses fenders will mark the centerlines of the hood.
The measuring tape on bottom corner of Hood - sure B. hook, measure from the hood corner (via hinges). Place a mark on just 10-3/4 on the fender conveyor and 22-1/2? on the hood tape (see table below model years)

The shift bracket is used for all Ducati Monster within the areas of the year 2000-2004. It can fit other years, but I can not guarantee accuracy did as minor changes over the years. The bracket is used, has to replace Signa tail light / turn / license plate Assembly and has rear section of the frame to which Assembly is pending. It is assumed that the frame has been removed already.

Warning: Cut or in any way change the frames can cause lead, that damage to the motorcycle and affect the performance and/or safety. I do not tolerate or cutting of the frame or the installation of the non-stock components on the bike in violation of local or state laws may be. Please check with your local authorities with regard to the legality of the installation of these components before continuing.