Archive for July 2012

Ferrari 328 Owners Manual

Ferrari 328 Owners Manual
Ferrari 328 Owners Manual inside is the manual talking about comprehensive collection, vehicle features, spurting manual, lubrication and repair charts - engine, standard reparation, radical employment, practice reparation, electrical system of the container. The informations cotained in this Ferrari exercise is strictly modest to the entropy essential for the use and fixture of the car. Providing that the pairing schedules are respected the costumer can be sure of obtaining the peak satisfaction and someone ensue from this vehicle download Ferrari 328 Owners Manual here
Read More Ferrari 328 Owners Manual
Posted in |

Hyuandai Azera KEY CUTTING Procedure and Programming

Hyuandai Azera KEY CUTTING Procedure and Programming
PROCEDURE: When an owner loses an Azera immobilizer key, the customer has two options to replace the lost key. Both options require that the customer bring the vehicle and any remaining keys to an authorized Hyundai dealer. Option # 1 The customer can use any remaining key originally supplied with the vehicle to drive to an authorized Hyundai dealer and request that a new key or key set be cut and programmed. It is important that the customer bring any remaining keys with them to the dealership. Any key that is not programmed (or re-programmed in the case of originally supplied keys) in the same operation will no longer start the vehicle. Option # 2 The customer can have the vehicle towed to an authorized Hyundai dealer and request that a new key or key set be cut and programmed. Again, it is important that the customer bring any remaining keys with them to the dealership. Any key that is not programmed (or re-programmed) in the same operation will be unable to start the vehicle. 1. If the Hyundai dealer does NOT have a Barnes Distribution BD Laser, they MUST call the Hyundai Motor America Parts Call Center at 1-800-545-4515 and make a request (order) for Azera immobilizer keys to be cut. NOTE: Azera immobilizer key blanks can be ordered either in singles (i.e. 1- master) or complete key sets (i.e. 2-master keys and 1-sub or valet key).
Nonetheless, HMA Parts System Centers gift exclusive pre-cut rank key sets upon communicate. They give NOT cut individual creation keys. 2. The Hyundai financier Staleness give the pursuing collection to the HMA Parts Inclination Middle. " VIN " Key Encipher " Moneyman Inscribe " Moneyman Accost (correct conveyance speak) " Moneyman Impinging (accurate denote of who the key should be delivered to) " Junction Phone Amount and Education 3. The HMA PDC testament help the conveyance of the key(s) to the concern de {must be programmed to the vehicle using a Hi-Scan Pro means. Mention: The Azera is accoutered with immobilizer anti-theft technology that instrument not grant the newly cut keys to signaling the object unless they bonk been gear programmed to the vehicle.
Read More Hyuandai Azera KEY CUTTING Procedure and Programming
Posted in |

Hyuandai Genesis Coupe Owner Manual

Hyuandai Genesis Coupe Owner Manual
TGS Commutation 1. Place the vehicle so it may be lifted on a lift and release the parking constraint. 2. Unbutton the modify lever kicking catch (A) and unprotected the shift lever flush. 3. Withdraw the fissure tumbler thickening by turning it counterclockwise. 4. Build the container off the percept and remove the energy armor by unfastening 6 mounting bolts (B). 5. Unfasten the two nuts (C) at the projection in fore of the catalytic convertor. Remark: Torque specification: 28.9 ~ 43.4 lb-ft. 6. Unfasten the two nuts (D) that introduce the parcel hanger on the lineman cylinder and vanish the area tubing unitedly with the thirdhand catalytic device. 8. Stretch a someone conductor across the anterior propeller upright caoutchouc connector (a) and the transmittal familiar projection(b). This leave be utilized to align when reinstalling. Discretion: Use fix not to exchange locations and directions of bolts and washers when reinstalling to forestall placement issues. 9. Disappear the 3 propeller airway mounting nuts Alter propellor upright to increase accession to the motion lever.
download
Read More Hyuandai Genesis Coupe Owner Manual
Posted in |

Wiring Connector Manual Guide Hyuandai ELANTRA CORROSION

Wiring Connector Manual Guide Hyuandai ELANTRA CORROSION
A facility leakage between the trickster outmost panel and cowl panels may resultant in corrosion of the proximity entranceway wiring connector pins if the object is operated in areas where means seasoning is utilized. The corroding may strike the cognition of the electrical circuits in the entryway, much as the speakers, nation windows, etc. To correct this status, reseal the seams and inspect the entrance wiring connectors for corrosion. If needful, position the entryway wiring connector and the entryway wiring by followers the couple procedures described in this TSB. SEALING THE Committee SEAMS: Comment: This sealing process applies to both nigh and modify sides.
1. Open the hood. 2. Locate the “A” pillar outer panel and cowl panel seaming area at the base of the “A” pillar. 3. Lift up the lower end of windshield glass molding to obtain space for sealant application. 4. Clean the sealant application area on both the left and right sides of the vehicle (fender removed in photo for clarity). 5. Apply clear sealant along the seam line between “A” pillar panel and cowl panel from the engine compartment as shown in the photo. 6. Use appropriate tool or finger (with rubber nitrate gloves) to smooth material to seal the sealant. NOTE: Apply enough sealant to completely fill the seam. Be careful not to drip excess sealant in the engine compartment or on the hood. – Photo shows panel seams where sealant is applied on left side. – Repeat for the right side. 7. Open the front door. 8. Apply the clear sealant to the seam between “A” pillar panel and the fender mounting bracket from inside the door opening. 9. Apply the clear sealant to the bottom of the fender mounting bracket and the top of the hinge. 10. Use appropriate tool or finger (with rubber nitrate gloves) to smooth material to seal the sealant. NOTE: Apply enough sealant to completely fill the seam. Be careful not to drip excess sealant on the door trim or in the interior. – Sealant is applied along the top edge of the fender bracket.

download from here
Read More Wiring Connector Manual Guide Hyuandai ELANTRA CORROSION
Posted in |

Volvo C70 transmission control module removal and installation

command module programming-read this first new transmission module (presura) is delivered without software. presura must be programmed to function after replacement. This requires the use of a tool for scanning the Volvo factory (Vadis), or equivalent. The software can be ordered only when the module is installed in the car. Vadis read outside the new identity of the management module. This is required so that the correct software can be ordered. Warning: wait two minutes after the ignition has been turned off before you remove the presura. before the module can be removed from the car, the main relay must be free. If the engine cooling fan is running on after the ignition is switched off, wait until it stops. then wait for a further 2 minutes. Caution: always check that the presura and presura connector pins and sleeves are not bent or damaged before replacing presura. This might have caused the fault. removal and installation 1. Move the shift lever Park (p) position. Turn off the ignition wait two minutes. 2. to remove the cover over the module on the right side of the engine compartment. control of transmission module (presura) is closest to the engine module. see Figure 11. Caution: do not touch the control module ensuring pin with fingers. static electricity may components of management module failures. 3. Insert instrument (999 5722), (1) around the module. see Figure. Move back the upper part of the instrument, as far as it will go (2). improvement of the tool. Carefully pull up on the control module. 4. gently press down in the grooves are a new module within the module control. Click to place the border! Insert tool 999 5722 around module. Move the upper part of the instrument next to stop and pull. Press the cover over the control. Check that the air ducts are position. 5. If you are installing new presura, programme of the new module for the management of the transmission. Check for dtcs, which may have been placed in memory during the repair.


Download

Read More Volvo C70 transmission control module removal and installation
Posted in |

Volvo S70 computerized engine controls removal and installation

Attention: ECM ECM, must not be removed from the car, while the main relay is interrupted power supply. This can take up to 150 seconds of motronic 4.4 systems after ignition has been turned off. car with an immobilizer can take up to 245 seconds after ignition has been turned off. removal and installation 1. as part of the system of securing against in cars equipped with an engine block the ECM in the engine compartment is locked in place with the locking Strip. locking Strip is installed by the security screw. see Figure 1. mark the center of the screw hole and made suitable for the puller screw. Insert screw puller and remove the screw. remove the security strap during the coverage of the module control. trimmed carefully of the coverage of the module of control so that there is no contamination or residue in the box when it is opened. 2. check that the supply from the main relay is interrupted. the easiest way is to insert the tip of the fingers of the idle air control valve. When the valve stops vibrating, the main relay is cut off supply to the system. 3. open the cover and remove the ECM motronic ECM (module closest engine). see Figure 2. 4. inspect the connector pins and the voltage for damage. Install ECM. contact scanning dlc. see Figure 3. Switch on the ignition. taking into account all the codes for the diagnostic abnormalities (dtcs). Delete the dtcs and restore adaptive functions, using the instrument scan.


Download

Read More Volvo S70 computerized engine controls removal and installation
Posted in |

Volvo S40 cabin air filters for removal and installation

removal and installation (2001-2004) 1. remove the underdash soundproofing for the passenger side. see the passenger's thermal insulation Panel. 2. Remove hook (). see Figure 3. 3. the cover for air conditioning air tubeis removed. 4. remove the particulate filter, using a twisting movement, downwards and away from the center of the console. 5. when the installation of the filter, check mark arrow on the lower edge of the filter. If the filter is marked with arrow, ensure the arrow points to a central console. install the passenger side acoustic insulation. passenger's soundproofing Panel removal and installation (2001-2004) remove the screw, clip and lower panel. see Figure 4. to install to remove.


Download

Read More Volvo S40 cabin air filters for removal and installation
Posted in |

Volvo S70 Glt heated oxygen sensor removal and installation

Remove ignition off. remove the air filter . Detach the inlet hose between the air filter and turbochargers of turbochargers. Open catch and shut down and two electrical connectors from the heated oxygen sensors. see Figure 41 and 42 of the figure. raise and support the vehicle. remove the left front wheel. reveal the top cabling. disconnect the electrical connectors. 9. raise and support the vehicle. 10. disclose lower cabling. 11. Remove sensor using a special instrument (999 5543) or equivalent. see Figure 43. installation 1. installation of the sensor using a special instrument (999 5543), or equivalent. see Figure 43. Tighten specification. see torque specifications . 2. secure lower cabling. a slight reduction of the vehicle. 3. electrical connectorsto connect. see Figure 41. secure cabling. 4. install the left front wheel. Tighten specification. see torque specifications .


Download

Read More Volvo S70 Glt heated oxygen sensor removal and installation
Posted in |

Tundra Hood protector installation of 2007 Toyota

() removal of external Grill plastic insert. remove the five (5) bolts from the grill. (Figure 2-1) (b) apply 1 7/8 "(48mm), mylar tapes are external bracket locations. (Figure 2-2) (c) open hood. attach external brackets using the nylon insert. (Figure 2-3) (d) to remove the 6 nuts in the grill to Hud locations. (Figure 2-4) (e) once the locks are removed from steps 2 (a) and 2 (d), Grill naturally must cause a gap at the top of the lid (Figure 2-5). If you need additional permission, slightly pushed the lattice to create a larger space. to account not to push extremely from lattice or outboard clips (not visible) can switch (Figure 2-6). (e) wash thoroughly. apply 3 mylar strips on the Hood and Grill, leave enough overlap to cover Hood. 43 "(1092mm) tapes to the centre section and add 4" (102 mm) pieces to cover the remaining area of the lid. (Figure 2-6) (g) gently slide shield spot and Center.


make sure that the shield is completely seated (Figure 2-7). If you need additional permission, slightly pushed the lattice to create a larger space. to account not to push extremely from lattice or outboard clips (not visible) can switch (Figure 2-6). Insert the screw through the center of the grill and Grill shield (Figure 2-7). (h) retighten all screws grille. (Figure 2-8). torque = 52 in-lbf (i) attach external brackets to cover with the aid of machine screws. (Figure 2-9) (j) to replace the bolts and replace the front Grill Grill plastic insert. (Figure 2-10) (k) remove masking from Hood protector. DownloadTundra Hood protector installation of 2007 Toyota

Read More Tundra Hood protector installation of 2007 Toyota
Posted in |

2007 Toyota Fj Cruiser for muffler installation guide

remove existing exhaust system. (1) remove the two bolts with springs of the front flange, located between the catalytic converter and rear muffler. (Figure 2-1) (b) keep all bolts of the original equipment (OE) and springs. (Figure 2-1) (1) ensure that the original Gasket between the remains of converter Assembly belt note: Dio, must be replaced install Gasket between the – p/n 17451-74051. (c) remove the two bolts from the rear flange, located between the muffler Assembly and installation of rear exhaust tailpipe is discharged.


(fig 2-2) (d) pry loose from rubber hanger, located near the rear bumperrear Calliper tailpipe exhaust. (Figure 2-3) (e) remove the Assembly of the oe rear tailpipe from the vehicle. pry the two front muffler exhaust brackets loose rubber handles. (Figure 2-4) (g) pry the two rear muffler exhaust brackets loose rubber handles. (fig 2-5) Note: the use of lubrication (for example "SOAP and water") of rubber exhaust handles can facilitate the removal and installation of rubber handles. (h) do not remove the five (5) original (OE) rubber handles from the vehicle. (i) remove the oe muffler Assembly from the vehicle. 3. install trd System. (1) connect the two front muffler handles the muffler Assembly of trd oe rubber handles. Download2007 Toyota Fj Cruiser for muffler installation guide

Read More 2007 Toyota Fj Cruiser for muffler installation guide
Posted in |

Volvo S80 t-6 Serpentine drive belt tensioner removal and installation

removal and installation 1. lift the power steering reservoir and place it on the engine. ensure that there is no oil leakage of negative Ventilation hole in the cover. 2. use a 15 mm wrench and turn clockwise as possible to lighten the burden on. lift off the serpentine belt. 3. to replace the belt tensioner, remove the mounting screws for tension of belt on serpentine belt bracket. remove the tensioner on the belt. install a new tensioner. tighten the specifications. see torque specifications . remove the serpentine drive belt and installation 1. lift the power steering reservoir and place it on the engine. ensure that there is no oil leakage outside the negative hole of ventilation in the coverage of. 2. use a 15 mm wrench and turn clockwise as possible to lighten the burden on. lift off the serpentine belt. Note: on some models, you may need to remove the vibration damper for replacement belt. Note: the manufacturer recommends replacement of the vibration damper-to-pulley bolts, if removed original bolts. 3. raise the car and remove the right front wheel plastic nuts from cover in the fender liner and regulator of the vibration. Use the running Center the nut as a counterhold. 4. use a 15 mm wrench and turn clockwise as possible to lighten the burden on. lift off the serpentine belt. remove the serpentine belt. 5. to install a new serpentine belt. see Figure 1. installation in the following order: crankshaft b. a/c compressor c. belt tensioner (d) generator e. steering pump 6. Install the regulator of vibration. Tighten the new bolts to specifications. see torque specifications . Use the nut as a counterhold running Center. use of logging protractor (951 2050). Install plastic nuts from cover in the fender liner. install the wheel. 7. install the power steering reservoir. Test the function.


Download

Read More Volvo S80 t-6 Serpentine drive belt tensioner removal and installation
Posted in |

2007 Toyota Fj Cruiser air dam/light bar installation

internal installation of switch/wire harness () locate the vehicle, White 6-PIN connector behind the lower instrument panel. (Figure 2-1) (1) Note: connector of the vehicle will be wrapped in gray foam tape. (b) installation of remote time switch (Figure 2-2), in available knockout (location 1 or 2), and in the orientation shown. (Figure 2-1) (c), plug the 6-pin white connector in the key. (1) confirm the connector is firmly attached. (d) the removal of the driver and passenger side visors. (1) rotate and loosen shaft support visor from visor holder clips as shown. (Figure 2-3) (2) does not remove clips from popular actor. (e) remove the sun visors (Figure 2-4) (1) remove the two Phillips screws (2) from the driver and passenger side visors.


To remove the driver and passenger side Assist grips. (1) remove the screw covers for all the claws four (4) assistance. (Figure 2-5) (g) remove the two (2) 10 mm hex head screws from the driver and passenger assist grips. (Figure 2-6) (h) "" pillar garnish to remove front passenger. (1) pull door seal around front "pillar". (2) places the two (2) videos and one (1) nail and remove the front pillar garnish. (Figure 2-7) (i) remove the front pillar garnish driver. (1) using the same procedure as the passenger's side. (j) to remove the mirror. (1) remove the mirror base mountain cover by careful insertion tool for Remove panel , as shown. Download2007 Toyota Fj Cruiser air dam/light bar installation

Read More 2007 Toyota Fj Cruiser air dam/light bar installation
Posted in |

Toyota Rav4 2Wd truck Steering Panel for removal and installation of 2007

Attention: do not forget to read the precautionary statements system of Srs cushion before servicing, refer to systems of service restriction. 1. disconnect the negative battery Terminal warning: at least 90 seconds after disconnecting the negative terminal, wait-the battery to prevent belt Pretensioner () activation and air bags. 2. Remove the direction the whole pad a. face of the front wheels. B. using a T30 Torx "driver, loosen two screws while a Groove along the length of each lap of screw catch in case of screw. C. download platform of the steering wheel and the management of maintenance of the keypad with one hand, as shown in the illustration.


Note: on the abolition of the D-pad, does not download cushion Wire harness. (D) using the screwdriver, disconnect the connectors 2 cushion. Attention: When the management of cushion clutch will not damage cushion Wire harness. E. disconnect the connector Jack and remove the plates to the direction. Installation warning: don't forget to read the precautionary statements system of Srs cushion before servicing. 1. install the platform management direction a. support pad with one hand, as shown in the illustration. B. connect the two air filters. Note: when handling cushion clutch will not damage cushion Wire harness. C. connect the Horn. (D) to install the Steering Panel after confirming that the slots of the circumference of the screws are traps in the event of a screw. DownloadToyota Rav4 2Wd truck Steering Panel for removal and installation of 2007

Read More Toyota Rav4 2Wd truck Steering Panel for removal and installation of 2007
Posted in |

Volvo S80 t-6 timing belt removal and installation

remove 1. remove the ignition key. Remove engine stabilizer bracket. the Turbo models remove the plastic pipes between the turbochargers and charge air cooler and between the turbochargers and air filter and work. fallow them. 2. Remove clamp from inlet manifold for compressor cylinders No 1, 2 and 3. inclusion of the upper part of the tube to the firewall. all models raise reservoir with power steering fluid and is placed on the engine. Note: 3. using the 15 mm wrench, rotate the ancillary drive belt tensioner clockwise to relieve the tension of the tape. see Figure 1. lift off ancillary drive belt. remove the upper timing belt cover. ensure power steering fluid does not leak from ventilation. 4. Remove air tube cover, surround and control module field. remove the thermostat housing and hose between the expansion vessel. remove the front timing belt cover. 5. seal the hose between the expansion tank and radiator. Disconnect the hose of the expansion vessel. lift expansion vessel and placed on the engine. 6. raise and support the vehicle. remove the right front wheel. Remove plastic nuts from cover in the fender liner. install the upper timing belt cover. 7. rotate the crankshaft clockwise until the timing marks are aligned. see Figure 2. Rotate the crankshaft a further 1/4 turn clockwise, then Rotate counterclockwise until the marks are aligned. 8. remove the upper timing belt cover. remove the 4 vibration damper screws. remove the vibration damper. Remove accessory drive belt. of models with hydraulic timing belt tensionergo to the next step. the models without hydraulic timing belt tensionergo to step 11. 9. install counterhold (999 5433) and remove the crankshaft Center nut. see Figure 3. Remove counterhold and accessories drive belt pulley. 10. remove the timing belt tensioner/hydraulic unit, then loosen the top screw bottom screw. inclusion tensioner hydraulic unit, so that the cylinder is free. remove the lower screw. remove the tensioner hydraulic unit. remove the timing belt. 11. remove the belt cover behind the crankshaft rolls for an auxiliary drive belt. spray universal oil around the rubber sleeve on the underside of the oil pump. Remove rubber bung. 12. slightly loosen the timing belt tensioner Center screw. hold the screw rotation. Nut to Rotate counterclockwise to eccentric use 6 mm hex wrench in eccentric, is 10 °hours position. see Figure 4. remove the timing belt.


Download

Read More Volvo S80 t-6 timing belt removal and installation
Posted in |

In 2005 Volvo V70 cabin air filters for removal and installation

1. Remove soundproofing Panel sprang from under the glove box. See thermal insulation Panel. 2. remove the screws for the cover for air filter of the passenger compartment. see Figure 1. remove the cover. 3. remove the cabin air filter by pulling downwards and outwards. installation Note: there are 2 alternative positions for the air filter. see Figure 2. Filter pollen (standard) must be installed in a compartment for smaller (1). multi filter (cars with sensor for air quality) must be installed in a wider compartment (2). Install the pollen filter or multi filter. both filters must be installed together. installation of the passenger compartment air cleaner and cover. Install the screws. front left screw must not be more than 7 inch lbs. (0.8 n. m). 2. install soundproofing Panel. soundproofing Panel Note: back of the soundproofing Panel is attached to the dashboard with clips and is located in the channel at the front. Remove and install, with the exception of the xc 90 1. Remove 2 screws from the thermal insulation Panel in field of wear. the clips pull straight down. 2. pull soundproofing panel back in the car. 3. lift soundproofing Panel. to install, you must restore the procedure for removal. removal and installation, xc 90 1. remove the underdash Panel. see Figure 3. 2. Remove 2 screws. 3. underdash, soundproofing Panel is removed. to install, you must restore the procedure for removal.


Download

Read More In 2005 Volvo V70 cabin air filters for removal and installation
Posted in |

2008 Toyota any Xd/Xb steering wheel alignment

1. align the steering wheel . (a) where it is centered parking to install leather steering wheel, the position of the vehicle, so that the front wheels are straight and the steering wheel vehicle. (1) turn the steering wheel rights position. (2) apply masking tape to the top center of the steering wheel and the steering column upper cover. (Figure 1-1) (3) draw a line bar masquerading as shown in the illustration. (Figure 1-1) 2. Remove battery cable. () remove negative battery cable.


(Figure 2-1) (1) protection of wings before you begin. (2) do not touch the positive terminal with any instrument in the removal of the cable. (b) srs cushion system backup power is active for 90 seconds after the negative cable is disconnected from the Terminal. Wait 90 seconds after the battery of the vehicle is disconnected before beginning step 3. (for safety cushion). Download2008 Toyota any Xd/Xb steering wheel alignment

Read More 2008 Toyota any Xd/Xb steering wheel alignment
Posted in |

1998 Toyota truck Tacoma extra cab 2Wd control Assembly removal and installation

1. remove the following parts: end of a. b. bottom panel glove compartment door c. lower panel complete with no. 2 2. Final panel remove cluster a. Remove key, A/management of c. b. Pull the enemy. C. Remove heater control plate. D. Remove 2 screws. E. using a screwdriver, remove the 4 mounting clips and the Panel is downloaded, then unplug the connector. Tip: Tape the tip of the screwdriver before use. 3. disconnect the cables Hater control tip: After connection, adjust the control cables. 4. to remove all control of heater remove 2 screws and remove the heater control Assembly, and then disconnect the connector. Installation of the installation is in reverse order of removal.


Tip: after the installation, set the heater control cables. A. mounting set control enemy under the following conditions: 1. the placement of the heater control Assembly in the "Cool" position. 2. "face" position 3 of dialing mode control . Temperature control dial for "Cool" position (b). set air intake cable. Pull my relationship of control as "Cool" position, connect cable and clamp bolt. Tip: Locking Pliers, lightly pressing on the outside of the cable in the direction as shown in the illustration. C. adjust the arrangements for power management. Pull my relationship of control as the "face" of the position, connect cable and clamp bolt. Tip: Locking Pliers, lightly pressing on the outside of the cable in the direction as shown in the illustration. Download1998 Toyota truck Tacoma extra cab 2Wd control Assembly removal and installation

Read More 1998 Toyota truck Tacoma extra cab 2Wd control Assembly removal and installation
Posted in |

Volvo 850 R cushion module removal and installation

Note: cushion module has a 10-digit identification number to be used when ordering replacement module. removal and installation (driver's side) 1. before you proceed, follow cushion service precautions. See precautions for service. disable cushion system. See Disabling and activating cushion system . 2. Turn key to start locking of the steering column . Remove steering wheel tilt adjuster (if available), steering column on the lower panel coating and strengthen set in the knee. 3. remove the 2 torx No. 30 screws from the rear of the steering wheel. see Figure 6. Pull airbag module from the steering wheel to break wiring connector. Install srs test resistor (988 8695) instead of the cushion module to prevent the formation of fault codes. see Figure 7. 4. to install, you must restore the procedure for removal. Tighten bolts cushion module specification. see torque specifications . turn key position. connect the negative battery cable. ensure the proper functioning of the system. See the operation of the verification system. 5. If, after the replacement cushion module fault code cushion module , clear the codes and verify the operation of the system again. If still srs warning light indicates a failure, type self-diagnostics and retrieve fault codes. See self-diagnostic system for diagnosis and testing. removal and installation (passenger-side) 1. before you proceed, follow cushion service precautions. See precautions for service. disable cushion system. See Disabling and activating cushion system . 2. disconnect the glove box lid. use the screwdriver and hand between each side of the bonnet, pry is hands. Remove the glove box torx screws and compartment. see Figure 8. Disconnect the seat cushion module connector from the lower side of the module. Remove 4 cushion module screws from the beginning of the glove compartment. 3. Remove side defroster outlet screw caps and screws. rotates a 4 vent nozzles down and removal. Remove nozzles and air duct on the right side. Remove speaker grilles and speakers. Disconnect the speaker connectors. Remove 9 retaining screws of the instrument panel and exclude the Panel cover from the top of the frame above the central console.


Download

Read More Volvo 850 R cushion module removal and installation
Posted in |

Volvo V70 instrument cluster removal and installation

removal and installation (c70, s70 and v70) excluding the negative battery cable. remove 12 cover Panel screws holding the instrument panel. see Figure. Disconnect the 2 instrument cluster connectors start Spring catches of the upper edge of the cluster. see Figure. 13. to install, you must restore the procedure for removal. removal and installation (s90 and v90) disconnect negative battery cable. Remove 2 cover panels and screws holding the instrument cluster. see Figure 14. lift instrument cluster. Remove connector seal. Unplug the connectors and remove the instrument cluster. to install, you must restore the procedure for removal. remove the fuel level sensor and installation (c70, s70 and v70) 1. fold down rear seat back rest. remove the boot room carpet. Remove panel to collect mobile leaves to the right rear wheel. Remove cover over the pump and the fuel level sensor. 2. excluding fuel level sensor connector and harness. unscrew the fuel level sensor plastic nut. see Figure 15. lift the fuel level sensor. to install, you must restore the procedure for removal. install a new rubber seal and Lubricate with petroleum jelly.


Download

Read More Volvo V70 instrument cluster removal and installation
Posted in |

1997 Toyota Avalon Xl steering removal and installation

Caution: disconnect the cushion before removing the steering wheel pad. 1997 Cushion restraint system or cushion article restriction. Remove 1. Place the front wheels turned forward in a straight line. 2. to remove the flywheel. Panel, see Remove wheel. 3. the engine must be switched off. Remove the flywheel nut. The wheel and place Matchmarks on the main axis. Use a set of Extractor c: Hanger 150, shoulder slide, Center of bolts, 150 and no. Nail 2 (SST 09920-50010, 09551-05010, 09552-05010, 09953-05020, 09954-05020), remove the wheel. See fig 27. Figure 27: removing the wheel arrangement of Toyota Motor sales, Inc., United States 4. Remove federšajbite PIN and remove the nut.


The use of a spherical exhaust (SST 09,610 to 20.012), a separate Tie rod end joint of the address. See Figure 28. Figure28: Rod separation connect points of steering ankle concert Toyota Motor SalesInc., United States, 5. Place Matchmarks on the intermediate shaft and axle of the regulating valve. See Figure 29. Screw a loosen and remove the bolt (b). Figure 29: disconnect the intermediate shaft 6. Off the plate. Remove the nut. 7. disconnect the pressure for power and pipes. Using the wrench 14 X 17 mm power steering hose the nut set (SST-09631 22020), turn off the tube. See fig. 30. Download1997 Toyota Avalon Xl steering removal and installation

Read More 1997 Toyota Avalon Xl steering removal and installation
Posted in |

2007 Toyota Tundra sport Shift knob installation

1. vehicle preparation. (fj Cruiser shown) () vehicle must be on the ground and not of incline/decline. (b) fully engage parking brake. (c) to remove the shift cover lock release. except for re-use. (Figure 1-1) (d) is pushed into the shift lock release button. (Figure 1-2) (e) place shifter the lowest gear. (Figure 1-3) 2. to remove oe shift button. () remove oe shift knob from turning o'clock counter-philosopher. (b) reject oe shift knob 3. Install the Shift button. (2) shift knob is installed rotate o'clock-wise. (1) when fully installed, there should be a 1/2 "+/-3/32" (12 mm +/-2 mm) gap between the bottom of the knob shaft to shift and shift gate,


the upper surface. (2 "barrel" of the shift knob must be oriented in the vehicle. (3) place a lever for change in "Park". (4) replace the shift cover lock release. (5) should be trimmed shift knob with-Scratch cloth. Download2007 Toyota Tundra sport Shift knob installation

Read More 2007 Toyota Tundra sport Shift knob installation
Posted in |

Volvo V70 Xc Awd oil pan removal and installation

removal and installation 1. before servicing the vehicle, refer to the section on safeguards. 2. drain the engine oil. 3. remove or disconnect the following: air intake Assembly oil with other Assembly right front wheel and inner fender liner splashguard 4 engine. remove the bolts for the oil cooling system and close the system side. 5. remove or disconnect the following: reduce the tube for the air of fee, if equipped pressure hose and return hose, starting from the power steering pump power steering hose bracket and move to one side additional drive belts a/c compressor oil pan to install: 1. install or connect the following: new o-rings for oil pan oil pan and tighten the bolts as follows: a. tighten bolts 123 and 4 to 24 inch lbs. (3 nm) b. tighten bolts to 18.5 ft lbs. (25 nm) and then to 35 ft. lbs. (45 nm) c. tighten all bolts to 13 ft. lbs. (17 nm). start of transmission and work forward in pairs. oil cooling system using new o-rings a/c compressor accessory drive belts pressure of oil and return hoses and hydraulics pump engine splashguard inner fender liner oil with other wheel air intake pipe 2. Start the engine and check for leaks. Fig. oil pan bolt identification-2005-06 s40/v50/c70 models oil pan bolt identification-2005-06 s40/v50/c70 models inline 6-cylinder engines is drained remove engine oil or disconnect the following: 1. oil with other pipe, 2. Turbo charge air tube, if equipped 3. Turbo air intake pipe, if equipped raise and support engine. remove or disconnect the following: lower engine cover air barrier in front of the front wheel oil filter lower ball joints nuts anti-roll bar links of anti-roll bar bolt right axle Center steering front engine mounting bolts from the torque rod, including support in the sub-frame wheel spindles


Download

Read More Volvo V70 Xc Awd oil pan removal and installation
Posted in |

1984 Toyota Starlet L4-1290Cc 4Ke time chain service and repair

Pension 1. Loosen water pump pulley. 2. Download the drive belt idling adjustment screw and remove the belt. 3. Remove the pump pulley water pump. 4. to remove the bolt on the crankshaft pulley Assembly. 5. with the help of SST (09213-31021), remove the crankshaft pulley. 6 Remove bolts and nuts supply chain, as shown in Figure 7. the use of a plastic hammer, loosen at the top of the chain and remove user. 8 remove the drive chain tensioner and time, vibration damper. Budget bolt remove the camshaft sprockets. 10. remove the chain and authority setting inbound. 11. remove the running body with a screwdriver.


If running body you cannot remove with screwdriver, using SST (09213-36020). Installation 1. Install running authority. 2. Set No. 1 TDC. 3. align the camshaft PIN with push plate. 4. to install the body to the circuit of the camshaft. Note: align supply chain and camshaft body mark time. 5. to install the distribution chain to the crankshaft body. Note: align supply chain and crankshaft body marks time. 6. to install body with chain camshaft. 7. Install and tighten the incoming body. Denomination: 54 to 63.5 Nm (40-47 Ft Lb.) 8. Install the drive chain tensioner regulator of vibration. Note: Apply oil tensor before installation. 9. Cover the installation time string Download1984 Toyota Starlet L4-1290Cc 4Ke time chain service and repair

Read More 1984 Toyota Starlet L4-1290Cc 4Ke time chain service and repair
Posted in |

2007 Toyota Tundra mounting kit installation instructions

Note the instructions for installation: for easier mounting and installation, vehicle and all snowplow components must be of smooth, level, hard surface, such as concrete. 1. on the side of the driver of the machine remove the remote clip securing the plastic bumper cover to start the dish. keep the knee to reinstall if the plow is removed. then fold the outermost of the plastic bumper cover for easier pushplate installation. 2. trim the splash Pan, as shown for easier pushplate installation. 3. Repeat steps 1 and 2 on the passenger's side. 4. on the driver's side of the machine remove the tow hook clasps and hook for towing. maintain a tow hook to reinstall if the plow is removed. keep the locks for reinstallation of the next step. 5. attach the driver's side to the frame of the pushplate truck, using the original latches hook towing. tighten hinges, so that the pushplate can be firmly against the bottom of the frame, but not fully reinforced at this time. 8.4-7 of the steps on the side of the machine is repeated. 9. to install the cross bar with four 1/2 "x 1-1/2" cap screws and 1/2 '' locknuts. hand tighten fasteners. 10. check connecting hand distance of 29-1/8 "+ 1/8". If the connecting arm distance is not within the 29-1/8 "+ 1/8 '', then loosen tow hook latches of either of the two pushplates and pushplate (s) in the direction to get move Download2007 Toyota Tundra mounting kit installation instructions

Read More 2007 Toyota Tundra mounting kit installation instructions
Posted in |
Powered by Blogger.

Search